Velleman WTC180T Manuel d'utilisateur télécharger pdf (Page 5)

WTC180T

V. 02 – 09/01/2013 5 ©Velleman nv

• Firmly hold the tile in place and gently slide the cutting disc [I] along the adjustable bridge [B]

towards the tile. Do not force. Always cut towards the graduated ruler [F], otherwise the spinning disc

will push the tile upwards.

• When finished cutting the tile move the cutting disc [I] back to the other end of the adjustable bridge

[B] and switch off the cutter by pressing the on/off switch [A]. Beware that the cutting disc keeps

spinning for a while before coming to a full stop!

• To cut tile edges under an angle, loosen both tilt angle lock knobs [D] and tilt the adjustable bridge [B]

in the desired angle (max. 45°). Secure the tilt angle lock knobs [D].

• After use, remove the power cord from the mains and dispose of the water in the water reservoir before

storing the tile cutter.

• When the cutting disc shows signs of wearing, replace it immediately. Refer to §8 for the correct

procedure.

8. Cutting disc replacement

Refer to the illustrations on page 2 of this manual.

Cutting disc replacement

1 motor shaft 4 outer flange

2 inner flange 5 nut

3 blade 6 shaft – narrow end

• Before replacing the cutting disc, switch off the tile cutter and remove the power cord from the mains.

• Remove the cutting disk guard [H]. To do this, remove the two screws [K] and lift the guard over the

cutting disk. Be careful not to damage the water hose.

• Place the included hex spanner over the nut [5] and place the shaft holder tool (included) over the

narrow end [6] of the motor shaft [1].

• Hold the shaft holder tool firmly and turn the nut [5] clockwise.

• Remove the nut [5], the outer flange [4] and the cutting disc [3] from the motor shaft [1]. Note that

the inner flange [2] has an edge which fits in the arbor hole of the cutting disc. Always mount the

inner flange [2] at the inside (closest to the engine)

• Make sure the new cutting disc has the right specifications (see §10). Never use segmented disc types.

• When spinning, the cutting disc rotates clockwise when looking from the narrow end of the shaft [6].

Always respect the rotation direction indicated on the disc!

• Slide the cutting disk [3] and the outer flange [4] over the motor shaft [1].

• Screw the nut [5] on the motor shaft [1]. To secure it tightly, place the included hex spanner over the

nut [5] and place the shaft holder tool over the narrow end [6] of the motor shaft [1]. Hold the shaft

holder tool firmly and turn the nut [5] counter clockwise.

• Remount the blade guard [H] with the 2 screws and washers (2 per screw).

9. Cleaning

• Keep the ventilation slots of the machine clean to prevent overheating of the engine.

• Regularly – preferably after each use - clean the machine housing with a soft cloth. Moisten the cloth

with soapy water when necessary. Never use solvents e.g. petrol, alcohol, ammonia… as these may

damage plastic parts.

10. Technical specifications

input voltage 230VAC / 50Hz

power 600W

IP-rating IP54

speed (idle) 2950 rpm

table tilting range 0~45°

dimensions 910 x 530 x 77 mm

table size 790 x 385 mm

disc Ø180 x 2.2 mm

arbor hole Ø22.2 mm

1 2 3 4 5 6 7 8 9 10 ... 27 28

Commentaires sur ces manuels

Pas de commentaire

Velleman WTC180T Manuel d'utilisateur Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Velleman WTC180T